| by admin | No comments

DATASHEET 2N2905 PDF

2N Low Power Bipolar Transistors. Page 1. 07/04/06 V Features: . Disclaimer This data sheet and its contents (the “Information”) belong to the. 2N Datasheet, 2N PNP Switching Transistor Datasheet, buy 2N Transistor. 2N Transistor Datasheet pdf, 2N Equivalent. Parameters and Characteristics.

Author: Akinozuru Voodoorr
Country: Sudan
Language: English (Spanish)
Genre: Music
Published (Last): 9 October 2016
Pages: 419
PDF File Size: 1.81 Mb
ePub File Size: 8.71 Mb
ISBN: 726-6-66705-887-2
Downloads: 75130
Price: Free* [*Free Regsitration Required]
Uploader: Tejas

Current flows in through collector, normally connected to load.

So if you looking for an NPN transistor that could switch loads or for decent amplification then 2N might the right choice for your project.

So to calculate the dstasheet value of datqsheet base we can use the formulae. The 2N is a NPN transistor and is normally used as a switch in many circuits. To make this current flow through the transistor the value of base current I B can be calculated using the below formula: Prices are subject to change without notice.

2N Datasheet, Equivalent, Cross Reference Search. Transistor Catalog

So the value if R B will be. Our People Search the directory for faculty or staff members. Search the directory for faculty or staff members. TL — Programmable Reference Voltage.

But this calculation will lead to the closest value to start with.

To make this current flow through the transistor the value of base current I B can be calculated using the below formula:. Current Drains out through emitter, normally connected to ground. Here lets us assume the load here consumes around mA maximum so our collector current I C datawheet.

  EL TRIUNFO DE LAS CIUDADES GLAESER PDF

But it comes in a metal can package and can operate on voltages slightly higher than what a 2N can handle. Since transistor is of NPN the load to be switched should be connected to the collector and the emitter should be connected to the ground as show in the figure below.

To see a list of open positions, click here. Where h FE, is the current gain of the transistor 2m2905 in our case is In our case for a collector current satasheet mA we have to pass a base current of 16mA.

Submitted by admin on 21 June To bias a transistor we have to supply current to base pin, this current I B should be limited to 5mA by using a transistor to the base pin.

Spring Semester, Monday — Friday: This stage is called Saturation Region.

SGS Thomson Microelectronics

Another important thing to keep in mind, while using a transistor as switch is the base resistor. For details on these services, please click the appropriate link from the menu on the left. In addition to supporting the various labs in the EL building, we also provide equipment and manual check-out and a wide range of electronic components datadheet sale. Engineering Program is accredited by: You can also see open positions in the department.

2N Datasheet(PDF) – Micro Electronics

When this transistor is fully biased then it can allow a maximum of mA to flow across the collector and emitter. However this vale will not be very accurate because the transistor will have an internal voltage drop across the collector current, so it mostly experimental to get the datashdet current from the transistor.

  10 CASOS DE FACTORIZACION ALGEBRA DE BALDOR PDF

Open Positions To see a list of open positions, click here. Where Vcc is the voltage on which the load operates and V BE is the voltage across the Base and Emitter which in our case according to the data sheet 1.

The ECE Store provides many services to electrical and computer engineering students in order to create a safe environment in which students have access to the equipment and parts they need. Welcome to the ECE Store.

Soldering Tips Helpful Link: Complete Technical Details can be found at the datasheet given at the end n22905 this page. Overall it is just another small signal transistor which is commonly used in switching and amplifying circuits. When base current is removed the transistor becomes fully off, this stage is called as the Cut-off Region and the Base Emitter voltage could be around mV.

As we know the transistor is a current controlled device meaning, we have pass some current I B thorough the base of the transistor to turn it on. The maximum amount of current that could flow through the Collector pin is mA, hence we cannot connect loads that consume more than mA using this transistor. This resistor is connected to the base pin of the transistor to limit the current flowing through the base.